12 Velvet Ribbon Christmas Garland Ideas for Deep Color and Soft Shine

This post may contain affiliate links. Please read my disclosure policy.

Click to share!

This is not a generic garland post. It is about one material: velvet ribbon, and what it does to a Christmas garland that no other ribbon can. Velvet drinks light instead of reflecting it, so its color goes deep and rich against evergreen, and its soft pile makes a plain grocery store garland look expensive in about ten minutes.

Thick red velvet ribbon tails hanging from a lush green garland in close up
Credit – Instagram @mollyrussellhome

These velvet ribbon christmas garland ideas come from real homes and shops, and every one is a ribbon technique: weaving a wide ribbon through the branches, tying bows with tails left long, repeating bows in a rhythm, mixing two velvet colors, or letting single tails hang like fabric. The first three are full builds with steps.

Buy ribbon like a decorator, not a crafter. For garlands you want wired edge velvet, two and a half inches wide for weaving and bows, one roll of ten yards per average mantel garland, in a color deeper than you think you need. Burgundy, forest, rust, chocolate, blush and burnt orange all appear below.

One safety note before the beauty: velvet ribbon is fabric, and fabric stays away from open flame, candle flames and hot bulbs. Keep tails clear of the fireplace opening and use LED lights in any garland dressed with ribbon.

Quick Picks

  • Start here: Weave Velvet Ribbon Through a Mantel Garland (idea 1)
  • Most photographed: A Repeat Rhythm of Velvet Bows (idea 9)
  • Biggest drama: Long Velvet Tails on the Staircase (idea 10)

1. Weave Velvet Ribbon Through a Mantel Garland

Credit – Instagram @lovely.harbor

The signature move: a wide dark green velvet ribbon woven in and out of a lush mantel garland, as on this white fireplace, where the ribbon reads like a river of deep color through the greenery. Weaving beats wrapping because the ribbon dives and surfaces, catching shadow and light, and the garland keeps its wild shape.

Use wired edge ribbon so every wave you press into the branches stays where you put it. Work in long, lazy S curves, tucking the ribbon deep, then pulling a loop of it forward. Dark green on green sounds invisible, but velvet’s matte depth against shiny needles is exactly the point, and it works with burgundy and chocolate too.

⏱ 35 minutes💲 Low🔧 Easy

Materials Needed

  • A mantel garland, plain evergreen
  • Wired velvet ribbon, 2.5 inch, one 10 yard roll, like this burgundy wired velvet ribbon
  • Floral wire or the garland’s own branches for tucking
  • Scissors
  • Optional: warm white LED string lights

How to Make It

  1. Hang or lay the garland first and fluff it fully. Ribbon woven into a flat garland looks flat.
  2. Anchor the ribbon end at the back of one end of the garland with a twist of branch or wire.
  3. Push the ribbon deep into the greenery, travel about a foot, then pull a generous loop up to the surface. Repeat in a lazy wave to the far end.
  4. Step back and even out the waves. Velvet should appear and disappear like a stream, not march in equal steps.
  5. Tuck the end at the back, then add lights last, in front of the ribbon but never touching hot bulbs to fabric.

Tip: If the ribbon keeps slipping, your garland is too sleek. Twist a branch tip over the ribbon at each dip. Faux garlands hold woven ribbon all season with no wire at all.

2. Tie Loose Velvet Bows All Along the Garland

Credit – Instagram @funcycled

This garland wears its velvet as a row of loose brown bows, soft and slightly untidy in the best way. A repeated bow is the fastest velvet technique there is: no weaving, no measuring, just the same simple bow tied again and again, and the chocolate brown against green and white is a quieter, modern palette.

Keep these bows imperfect on purpose. Two loops, two tails, a pinch in the middle, and tails cut at different lengths. Perfectly matched bows look like a shop display; slightly loose ones look like a home. Brown, taupe and blush velvet all give this soft effect.

⏱ 40 minutes💲 Low🔧 Easy

Materials Needed

  • A hung garland
  • Velvet ribbon, 2 to 2.5 inch, in one soft color
  • Scissors
  • Thin wire or twist ties for attaching

How to Make It

  1. Cut ribbon lengths of about thirty inches each. For a six foot garland, plan five to seven bows.
  2. Tie each length into a simple two loop bow in your hands, knot at the back, tails uneven.
  3. Wire each bow to the garland at even spaces, sitting on top of the greenery, not buried in it.
  4. Fluff each bow’s loops open with your fingers so the velvet pile catches the light.
  5. Trim tail ends at an angle, and steam out any hard creases if the ribbon came off a tight roll.

Tip: Tie all the bows first in a pile, then attach them. Tying bows directly on a hung garland makes every bow a slightly different height and drives perfectionists mad.

3. Crown the Garland With a Trailing Velvet Bow Wreath

Credit – Instagram @christophercollection

Above many great garlands hangs a wreath, and this one shows how to join the two: a lush wreath wearing a large taupe velvet bow whose ribbon trails down in long streamers. The wreath bow becomes the garland’s crown, and the trailing tails stitch the wreath and mantel into one picture.

Taupe and stone velvet are the sophisticates of the family. They glow against deep green and let gold and glass ornaments shine. Cut the tails long, nearly touching the mantel, and let them fall at slightly different lengths with the ends cut in soft points.

⏱ 30 minutes💲 Low🔧 Easy

Materials Needed

  • A plain evergreen wreath
  • Wide velvet ribbon, 2.5 to 4 inch, in taupe, stone or your garland color
  • Wire for the bow center
  • A hook or ribbon loop for hanging

How to Make It

  1. Cut a generous length of velvet, about two yards, for one big bow with long tails.
  2. Form two large loops, pinch the center hard and bind with wire, leaving the rest of the length as falling tails.
  3. Wire the bow to the lower third of the wreath, the spot the eye lands on first.
  4. Hang the wreath centered over the garland and arrange the tails to fall in front of the greenery.
  5. Adjust loop shapes last, opening them wide so the velvet reads from across the room.

Tip: One big bow beats five small ones above a garland. Scale is what makes this look designer: the bow should be at least a third the width of the wreath.

30% OFFPrintable Christmas bundle with planner, advent activity cards, gift tags and family games

Printable Bundle

Christmas Printable Bundle

Christmas planner, 24 advent activity cards, 36 gift tags, handmade labels, Santa letter and family games.

$9.99$6.99SAVE 30%Instant PDF download
Get the Bundle

4. One Big Bow, Close Up and Unashamed

Credit – Instagram @goodwill_thrifty

This close up of a large dark red velvet bow hanging in front of an evergreen mantel piece shows velvet’s whole argument in one frame: the pile, the shadow in its folds, the depth of the red. If your garland is simple, one bow like this, hung at the center or the corner, is the entire decoration. Size up, hang it proud, and let the material speak.

You’ll need: one wide velvet ribbon length, wire, a garland or mantel greenery piece

Best for: simple garlands and thrifted finds

5. Hang the Tails Long and Let Them Fall

Credit – Instagram @mollyrussellhome

Thick red velvet ribbons hanging straight down from a lush garland, as in this close up, turn ribbon into fabric: the tails move slightly, catch light along their edges and give a mantel the softness of a curtain. Tie simple knots or small bows at the top and let the tails fall twelve to eighteen inches, cut level or pointed. Keep them well clear of any flame below.

You’ll need: wide red velvet ribbon, cut in long lengths

Best for: high mantels and dramatic rooms

6. A Giant Velvet Bow on the Entry Garland

Credit – Instagram @kazahomee

This contemporary entryway wears a large dark red velvet bow on its elaborate Christmas dressing, and the bow is what guests will remember. Outdoor and entry garlands need one big gesture because they are seen from a distance and in flat daylight. Velvet reads at twenty feet where small ornaments vanish. Use outdoor safe ribbon near doors and check it after storms.

You’ll need: extra wide velvet ribbon for one oversized bow, strong wire

Best for: front doors and entry garlands

7. Burnt Orange Velvet on a Marble Mantel

Credit – Instagram @kliraworld

A white marble mantel with a garland of greenery, eucalyptus and berries finished with an orange velvet accent, as here, proves velvet is not only red and green. Burnt orange velvet against cool marble and blue green eucalyptus is a modern, almost autumnal Christmas that still feels festive. Try rust, ochre or copper velvet if your room runs warm and neutral.

You’ll need: burnt orange or rust velvet ribbon, an eucalyptus mixed garland

Best for: marble mantels and modern rooms

25% OFFPrintable Christmas party games pack with trivia, charades, who's most likely to and gift swap games

Printable Games

Christmas Party Games Pack

9 fun games for family, friends and office parties: trivia, charades, gift swap and more.

$7.99$5.99SAVE 25%Instant PDF download
Get the Games

8. Cascade the Garland Down the Mantel Side

Credit – Instagram @enchantingdesignsmi

This mantel corner lets the garland pour down one side in a cascade, and a deep red velvet ribbon pours with it, its tails falling through berries, birch ribbon and gold ornaments. A cascade is the stylist’s trick for narrow mantels: the decoration goes vertical instead of wide. Velvet ribbon is ideal for it because its weight makes it fall straight and true instead of floating.

You’ll need: a long garland, red velvet ribbon with long tails, ornaments for the cascade

Best for: narrow mantels and fireplace corners

9. A Repeat Rhythm of Velvet Bows, Two Colors

Credit – Instagram @madeby_clare

Blush pink and burgundy velvet bows alternate along a wall garland of pine, berries and cones in this joyful shot, and the rhythm is the design. Two velvet colors, one bow shape, even spacing: it looks planned by a professional and takes an afternoon. This works over a sideboard, along a hall wall or above a bed’s headboard, anywhere a garland runs in a straight line.

You’ll need: velvet ribbon in two colors, a straight run garland, even spacing

Best for: walls, sideboards and headboards

10. Big Velvet Bows Down the Staircase Garland

Credit – Instagram @christmas_heaven

A staircase garland with lights, burgundy velvet bows at every swag and velvet bowed gift boxes on the steps: this is velvet used at full scale. Staircase garlands are long, so the bows must be big, at least six inches across, or they disappear. Tie one bow at the bottom of each swag where the garland dips, and repeat the same ribbon on the stair gifts to pull the whole staircase together.

You’ll need: burgundy velvet ribbon in quantity, big bows at each swag

Best for: staircases and entrance halls

11. A Velvet Bow With Brass Bells at the Mantel Corner

Credit – Instagram @suzi_yasu

On this stone mantel, a cedar garland ends in a burgundy velvet bow hung with three brass bells, beside tall candles and a winter print. The bow does double duty: it finishes the garland’s end, which is always the awkward part, and it gives the bells a soft, rich hanger. Any garland end, corner or joint can be hidden under one good velvet bow.

You’ll need: a velvet bow, brass bells on a loop, a garland with an awkward end

Best for: mantel corners and garland ends

12. Long Rust Velvet Tails on a White Mantel

Credit – Instagram @orlasoasis

Long rust colored velvet tails hang from this white mantel’s garland of eucalyptus, gold and dried orange, falling almost to the floor of the fireplace. Tails this long are pure theatre, and velvet is the only ribbon heavy enough to hang this straight. Measure tails to end above the hearth, never in it, and keep this look for fireplaces that stay unlit or use LED candles nearby.

You’ll need: rust velvet ribbon in long lengths, a mixed eucalyptus garland

Best for: unlit fireplaces and styled mantels

Frequently Asked Questions

How much velvet ribbon do I need for one garland?

For a six foot mantel garland, one ten yard roll of two and a half inch wired velvet covers weaving with generous waves, or about seven tied bows, or three bows with very long tails. Staircase garlands need two to three rolls. Velvet bows use more ribbon than they look like, so buy the extra roll; leftover velvet wraps gifts beautifully.

Wired or unwired velvet ribbon for garlands?

Wired for weaving and for bows that must hold a shape, which is most garland work. The wire lets you press waves into the greenery and open bow loops wide, and they stay all season. Unwired velvet is better only for hanging tails, where you want the ribbon to fall and sway like fabric. Many decorators keep one roll of each.

Which velvet colors look best on a Christmas garland?

The deep ones: burgundy, forest green, chocolate, rust and burnt orange, because evergreen is dark and pale ribbon can look washed out against it. Blush and taupe work when the garland is light or flocked, or the room is pale. The rule is contrast in value: the velvet should be clearly darker or clearly lighter than the greenery, never the same tone.

How do I stop velvet ribbon from creasing and crushing?

Store rolls loosely, never folded, and steam creases out gently rather than ironing, since a hot iron flattens the pile and leaves a shine mark. If you must press, use a cool iron on the back with a cloth between. At season’s end, roll bows and tails back onto the empty spool and store them in a box, not a bag.

Is velvet ribbon safe on a garland near a fireplace?

With distance and sense, yes. Keep ribbon and tails out of the firebox opening, away from the flue and off any surface that gets hot, and never let tails hang where a flame or a rising spark can reach them. Use LED lights in ribbon dressed garlands, keep candles in holders away from the greenery, and if the fire is lit nightly, keep the ribbon high on the mantel only.

Can I reuse the same velvet ribbon every year?

Yes, and good velvet improves with keeping. Shake it out, steam it lightly, and it will serve for many seasons, which is why one quality roll beats three cheap ones. Retie bows fresh each year rather than storing tied bows, which crush in boxes. Colors like burgundy and forest never date, so the same ribbon can carry a decade of Christmases.

Final Thoughts on Velvet Ribbon Christmas Garland Ideas

Velvet ribbon christmas garland ideas all rest on one truth: the ribbon is not the trim, it is the event. Weave it deep, tie it loose, hang its tails long and let its dark, soft color do what ornaments cannot. Start with the woven mantel garland, add a crowned wreath or a rhythm of bows, and a plain evergreen garland becomes the richest thing in the room.

Click to share!

Amir Ali
Amir Ali

Amir Ali is the founder of HomeDecorEdge, sharing practical and beautiful home decor ideas for apartments, small rooms and family homes.

Articles: 547